- Видео 410
- Просмотров 3 965 432
Veikra
Канада
Добавлен 6 сен 2009
I do car repairs and electronic repairs, Often it applies to both, fixing electronic issues on cars and trucks.
How to test audi a8 d3 soft close latch
Simple test to make sure the latch portion of the soft close system works correctly
Просмотров: 243
Видео
2014 Toyota Yaris C1407 Code, ESP ABS lights troublecode
Просмотров 5035 месяцев назад
An obvious wiring issue on many toyota models. Wiring must be adressed to correctly repair. Sensor replacement would not fix this issue. A trap for the part swappers !
Remember this trailer trick this WINTER
Просмотров 2999 месяцев назад
Get those frozen trailer locks off without any tools
The Audi 4.2 Cdra Achille`s heel
Просмотров 43510 месяцев назад
The 2011 CDRA found in 2011 audi A8 and A8L rarely survives a thermostat replacements. This is why I won`t do thermostat replacement without changing this other part as well.
Inside the 4.2liter audi V8 intake ports | No carbon
Просмотров 1411 месяцев назад
Just cleaned the carbon out of this CDRA 4.2 V8
Shire horse stolen by CHICKEN
Просмотров 7611 месяцев назад
The horses arent afraid of chickens. If there was danger those chickens wouldnt be allowed to jump on them. They are free desensitization around calm horses so no harm no foul.
Princess broke the fence
Просмотров 603Год назад
must have leant over the fence and crushed it with her neck
Mounting a shire horse. No saddle and no problems!
Просмотров 241Год назад
These actions are most likely to get you killed. Im perfectly safe, this is not a random horse.
1976 Cadillac Deville Oil Change.... but what's that clicking noise?
Просмотров 858Год назад
" It hasnt driven since, so that oil is perfectly fine "
I have nothing agasint dandelions but...
Просмотров 43Год назад
...found a enjoyable way to get rid of them We`re out of mud and into green season ! Turandot is slowly getting back in shape and weight after her first foal in many many years. I`ve been lax on video as I do not have time to edit lately. Ive got many car vids in the works, whenever I get to it.
Atrocious rebuild quality control
Просмотров 131Год назад
I've been replacing steering gears every 10 000km, and this new rebuild is slack even BEFORE I install it. I use GM factory powersteering fluid, I have a power steering oil cooler fitted. I have returned it, waiting on another one and cannot use my truck. All are under warranty claim but my time is not compensated. I could use a nice PSC unit and should have bought one in the first place. Buy c...
Shire horse takes a detour because of different camera than usual
Просмотров 73Год назад
Shire horse takes a detour because of different camera than usual
Doing a wheelies with a big road grader.
Просмотров 245Год назад
Doing a wheelies with a big road grader.
D4 Audi A8 Air Spring ONLY replacement.
Просмотров 9 тыс.Год назад
D4 Audi A8 Air Spring ONLY replacement.
Windcharger Princess 3 years old still growing!
Просмотров 77Год назад
Windcharger Princess 3 years old still growing!
D4 Audi a8 2011-17 front air strut removal
Просмотров 5 тыс.Год назад
D4 Audi a8 2011-17 front air strut removal
I'd call him Phantom but he`s sold along with naming rights. Oh well
Просмотров 98Год назад
I'd call him Phantom but he`s sold along with naming rights. Oh well
Shire horse standing up after sleep. Gray Shire Mare
Просмотров 2602 года назад
Shire horse standing up after sleep. Gray Shire Mare
2011 AUDI A8 CDRA VALVE COVER GASKET
Просмотров 3,3 тыс.2 года назад
2011 AUDI A8 CDRA VALVE COVER GASKET
Delorean Mode Wheel Bearings replacements AUDI A8 D3
Просмотров 2,3 тыс.2 года назад
Delorean Mode Wheel Bearings replacements AUDI A8 D3
Tool trick only canadians know #shorts
Просмотров 1122 года назад
Tool trick only canadians know #shorts
Shire horse filly's first day without Mom.
Просмотров 622 года назад
Shire horse filly's first day without Mom.
COLD start and clearing snow with walk behind snowblower
Просмотров 902 года назад
COLD start and clearing snow with walk behind snowblower
"You move " "No, YOU move, throw a tantrum if you wish..."
Просмотров 1002 года назад
"You move " "No, YOU move, throw a tantrum if you wish..."
How many quarts it takes on oils ? I have a 76 deville as well
are those intake manifold linkages stock 😅
Don't drill the rivets. Jesus. Just disassemble the console and do a proper paint job. Lol.
I have a no crank no start on a 2014 accent. It has new crank position sensor,new battery and new low fuel pump. What’s the first sign of bad starter?
Hey quest do I need to remove the valve covers in order to get the intake out
Hello man thanks for video I have a question about audi a8 d3, there are many mistake lights on control panel like as abs esp and big attention sign. But no sign of malfunction because car is move good, how can I fix and delete this mistakes and what should I do
HI I NEED TO MAKE 4 PORT FEUL PRESSURE REGULATOR/DAMPER TUTORIAL
No focus on the switch on the actuator
Best educational video I’ve seen on that particular job on a 4.0. Thank you very much sir!!
Useless ass video bro
Can you even buy that USC paint stripper anymore?
Is the hoses the same for the lbz2007
bro great job but what accent is that?
Great video, thanks a lot. I received two bags from China, it seems all the top seals are included. What are the set of keys you have at 5:43 to release the connector? Thanks again!
25:48 ok! Donc faire la distribution sans respecter la procédure, engendre une forte consommation de carburant !!! Big merci à toi mon frère ! Car j’ai, justement, une forte consommation d’essence. Et je vais y remédier grâce à toi🙏😉
10:35 clik clik clik au démarrage… c’est à cause du tendeur de chaînes d’arbres à cames !!! Ok ok. Merci beaucoup. Mais après avoir remplacé les tendeurs de chaînes d’arbres à cames, comment remettre les arbres à cames en place bien orienté? (bien caler, bien droit. Est-ce qu’il y à un repère, ou une encoche , Ou quelques choses pour indiquer le bon emplacement ?)
What's the paint color for the speaker grills? I want to repaint mines and your color is the same as mine
There ias no need for any seel on the shaft , centifugal force of the spinning prevents any leakage along the shaft , I know what you are doing is well intentioned but it will not make the slightest difference . How do i know this; I am a time served heating engineer.
This video is like some one goes to the repair shop have the work done and ask for the old parts and make a video and show no work (the car looks great)
I have the same snd woring done , but now become worest
Is age or mileage more important when determining whether a timing belt is still good? My A8 only has 50k kms added since the timing belt was replaced but the belt was replaced but it was replaced almost 12 years ago. I'm going to be replacing the belt anyways just to be safe but what do you think?
Is the distribution the same, for the Audi 3.7l v8 2004 280hp please? (Clamping torce, same camshaft setting bar, pige ect...)
Est-ce que c’est pareil la distribution, pour la Audi 3.7l v8 2004 280ch svp? (Couple de serrage, même barre de calage arbres à cames, pige ect… )
Oui, le 3.7L BFL de meme année partage presque que tout apart la cylindré.
Yeah what if the whole sides and roof part are completely gone rusted is it still possible to just cover everything in bondo and sand it and sculpt it to the original form? It would be hard as fuck because it has to be perfect for the door seals and the windshield gasket to fit
No, it wouldnt hold. You need a donor frame to weld in there
So your purge valve was leaking air into the system but had no fuel leaks ?
yes, suction from injection pump would draw air in. I had no lift pump back then
@@VeikraI’m running into issues with my truck, It’s was puffing clouds of white smoke threw in my scanner it showed misfire in cylinder 5, changed that one injector and it fixed it for a day now it’s back to puffing slight clouds under acceleration
I’m no diesel mechanic but I understand what it needs to run
I’ve been dreading on taking it to the shop because I know it’s going to cost me a arm and a leg for diagnosis
And labor
Thank you ,, good job
Welcome
I have issue at abs still even I make the wiring
Post VCDS scan of abs module please
Mine is throwing p0193 fuel rail pressure low during power enrichment, only does it while towing on a steep grade. Things I've done New cp3 Filter housing rebuild New fuel filter Ppe race plug New fuel lines inside engine bay Any help is appreciated please
You have one or many injectors with a higher than normal return rate. Have the return rates tested, you'll see. Truck can run perfectly fine then fall flat the next second and that is exactly the code that will pop up. Procedure is simple, you unhook the return line and stuff them in a graduated cylinder for x amount of time. Look it up
That multi tool your using fives off the impression that you're a butcher. As if that wasnt bad enough i had to watch you slop glue all over the place. This review is for anyone thinking this work is the standard practice for this repair. Its not
there is no pretension that this is a hack, as said in the video. I even say out loud i'll be replacing it later. But 7pm on a friday and the car show is already started. Aint no overnight parts from japan!
Bay weip saet address
How did you do that change on yours i have the same model and need to find out how to in stall them
I dont know what else you need to know. The steps are explained in the video. You want to see the wrenches turning?
I was on the fence about buying one. Thanks for confirming how good it is, I'll definitely get one !
Wait, I"ll put my affiliate link in the description so you can buy it for "cheaper"
from Quebec? Im just inspecting my 2009 toyota corrola for rust around the top of the roof near the windshield... my problem is my windshield is in good shape... pulling it out and putting it back is out of my skill set... i might need to get this done by a carrosie
I'm in the greater Montreal area. You could get a glass professionnal to pull it and put it back.
@@Veikra a mobile unit?... that would be the best bet... they come take it out, I fix the rust over a couple days, then they put it back... I was going to pass by a salvage yard and get a spare windshield if mine cracks for whatever reason...the Kenny Upull in LaPrarie has a 2010 corrolla there that I needed a part from that had a good windshield... to be continued 😁
Do they smoke when driven at high temperature?
what to you mean high temperature?
@@Veikra Operating temp. Smoke coming out from underside. Havent figured out source yet
@@oaggie73mine is doing the same thing I still can’t figure it out but I definitely have fuel in my exhaust so it smokes as it warms up
Does the A8 2008 4,2 gasoline also have belt?
no, 2008 is a chain on the a8
@@Veikra Ah ok.
What tools are needed for the job
nothing fancy, torx bit in very small rachet required for some bolts
Hey buddy my name is Patrick an I'm doing the same swap on my 03 Duramax an I would like to ask you a couple of questions if you don't mind I took the wires out of the doner harness that needed an installed them into my factory harness pin for pin the only wires i have left over that are not hooked up are a pink wire, yellow an brown with a white stripe that went to the doner harness at the left front kick panel plug do I need to splice them into my factory harness or are they not used also everything works other than my heated seats on both sides im not sure what to do any help would be much appreciated!
hard to tell which wires those are. As I said in video, the color changes between model and years. For instance, my harness is avalanche instead of sierra so almost no colors. Can you make a video and show both harness? Its been years since I've done mine
Hey man same problem here. Brake works just fine when I pull it and push it but somehow it beeps all the time as if it is still on while none of the brakes are active. Driving became hell and I am not able to go to a mechanic . I am thinking of cutting off the EPB fuses just so this annoyimg sound goes away. I dont need handbrakes either. What would you say?
It`s a parking brake motor that froze. There is a bearing in there that can rust if the parking brake isnt used often. An D3 a8 will beep over 10 km/h for 1 minute straight. Then it if you go below 10, it will reset and it will beep another minute once you resume driving over 10km/h. If the motor is frozen, it will log a fault. Supply voltge for EPB motor either left or right I've opened and fixed those motors with 100% success rate but I have access to a lot of tools. It`s always the frozen bearing for lack of use, or the connector that got corroded. I would rather fix it that delete it. You will have more problems than you think deleting it. on the a8, the car mesures brake pad thickness with this motor. So you will have 2 permanents malfunction light flashing in your dash, with the beeps on startups, plus a brake pad worn message. Get a used caliper, remove the motor and replace yours, then cycle the parking brake 3 times. Done deal and you`ll only MAYBE need to set pad thickness
What did you use to cut
x acto knive
I thought the 4.2 had a timing chain, in the rear of the motor?
4.2 is only the displacement. There is dozens of different 4.2 engine models. Some with belts, some with chains. All the newer ones are chain, though. The BFM and BGK of the audi a8 and a8l are some of the best v8 ever made.
@Veikra I picked yp a 98 a6 with a 2.8 5v. 109k miles, everything but abs works...for now. Very well taken care of, doin timing belt, thromostat and valve cover gaskets next month
Thanks so much for posting these! Recently grabbed a 447 I'm about to tear into.
I reconditionned a lot of 447 and 445. If you have any questions let me know.
What size of hose did you use ? My truck is having the same symptoms
1/2 inch ID for feed. Returns are 3/8 ID
Does anyone know what the purple and brown connection are for that go to the BCM and fuse panel? Just installed a donor harness that didn't have these but had factory heated seats. Wondering if all I need know is a factory door switch to turn the seats on? Do I need those two plugs for the heated seats to work? Any help is greatly appreciated.
2003 and up do not require any door harness. The switch in the door connects to the window switch and uses the CANbus to talk to heated seat module
@@Veikra do you know what the purple connection that went into the bottom of the BCM is for? Same with the brown connection that was with it that went to the fuse box on the side of the dash.
@veikra, do you know if I need the purple and brown connection to get the heated seats to work? I bought a switch and it has power, but no orange lights for the heat. Thanks.
I installed the harness out of a 03 into my 05. I bought the factory heated seat switch and connected it into my door switch. It has power just not the orange light for heat. Do I need a different BCM? Or do I need to reflash the one in the truck? Any help is much appreciated
I make them out of old washers. Basically the same as you did. 👍
good idea!
Thanks for this Veikra. Very helpful. What make of hub did you use? Is MOOG a dependable brand? I also have to replace the lower and upper arms. All bushing is shot. Thanks again.
at least MOOG has a warranty. It's what I use. Always avoid cheap bearing, they arent worth it, and fail prematurely
Any tips on cv axle shield rounded out bolt???
yes, aligne a large punch with a flat base. Needs to be perfectly flat on the head of the bolt. It will shrink it back. Otherwise cut the bolt, the treads are never stuck. You can also force a old torx inside of it, but you need a impact rated torx. Good luck
@@VeikraI managed to get it. Will be making crankshaft sensor video soon
Every upload makes me happy. There is rarely and video on a8 d3 gen in usa at least... thank you for providing these informations.
Great video! Thanks for sharing!
Thank you
Update. I have now blown the new unit I got after this one. Same thing, the output shaft is wallowed out and moves sideway and ate the seal !
hey dude is there anything to look out for when replacing the entire motor with a new one?
Not on the a8. It will self calibrate as the a8 motor is a torque sensing unit.